Autostart PD-2.7 Guide de l'utilisateur Page 155
- Page / 170
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Spartan-6 FPGA Configuration User Guide www.xilinx.com 155
UG380 (v2.7) October 29, 2014
SelectMAP Reconfiguration
The ABORT sequence lasts four CCLK cycles. During those cycles, the status word changes
to reflect data alignment and ABORT status. A typical sequence might be:
11011111 => DALIGN = 1, IN_ABORT_B = 1
11001111 => DALIGN = 1, IN_ABORT_B = 0
10001111 => DALIGN = 0, IN_ABORT_B = 0
10011111 => DALIGN = 0, IN_ABORT_B = 1
After the last cycle, the synchronization word can be reloaded to establish data alignment.
Resuming Configuration or Readback After an Abort
There are two ways to resume configuration or readback after an ABORT:
• The device can be resynchronized after the ABORT completes.
• The device can be reset by pulsing PROGRAM_B Low at any time.
To resynchronize the device, CSI_B must be deasserted then reasserted. Configuration or
readback can be resumed by sending the last configuration or readback packet that was in
progress when the ABORT occurred. Alternatively, configuration or readback can be
restarted from the beginning.
SelectMAP Reconfiguration
The term reconfiguration refers to reprogramming an FPGA after its DONE pin has gone
High. Reconfiguration can be initiated by pulsing the PROGRAM_B pin (this method is
identical to configuration) or by resynchronizing the device and sending configuration
data.
To reconfigure a device in SelectMAP mode without pulsing PROGRAM_B, the BitGen
-g Persist option must be set—otherwise, the DATA pins become user I/O after
configuration. Reconfiguration must be enabled in BitGen. See Table 5-3 for a list of pins
affected by Persist in the SelectMAP configuration mode.
D4 IN_ABORT_B
ABORT in progress (active Low)
0 = Abort is in progress.
1 = No abort in progress.
D3-D0 1111 Fixed to ones.
Table 9-2: ABORT Status Word (Cont’d)
Bit Number Status Bit Name Meaning
- Spartan-6 FPGA 1
- Configuration 1
- Revision History 3
- Table of Contents 7
- Chapter 4: User Primitives 8
- Chapter 8: Readback CRC 10
- About This Guide 13
- Additional Resources 14
- Configuration Overview 15
- Design Considerations 16
- Slave Modes 17
- UG380_c1_02_051109 18
- Serial SelectMAP 18
- MultiBoot /Safe Update 20
- Required I/O Voltages 20
- Nonvolatile Data Storage 20
- FPGA Density Migration 21
- Production Lifetime 21
- Configuration Factors 22
- Chapter 2 23
- Master Serial 26
- Slave Serial Configuration 27
- Spartan-6 28
- Microprocessor 28
- Platform Flash 32
- SelectMAP Data Loading 35
- SelectMAP Data Ordering 39
- SPI Configuration Interface 40
- SPI Flash 42
- W25Q SPI 43
- UG380_c2_14_011310 44
- Master SPI Timing Waveform 45
- Power-On Sequence Precautions 46
- SPI Serial Daisy-Chain 47
- Chapter 3 59
- Data Valid 60
- User Primitives 65
- ICAP_SPARTAN6 66
- STARTUP_SPARTAN6 67
- SUSPEND_SYNC 68
- POST_CRC_INTERNAL 69
- Chapter 4: User Primitives 70
- Configuration Details 71
- Pin Name Type 72
- Description 72
- Bitstream Overview 75
- Generating PROM Files 77
- UG380_c5_01_042909 78
- Parallel Bus Bit Order 79
- Configuration Sequence 80
- Setup (Steps 1-3) 81
- UG380_c5_04_050812 82
- Sample Mode Pins (Step 3) 83
- UG380_c5_05_042909 83
- UG380_c5_06_042909 83
- Synchronization (Step 4) 84
- Check Device ID (Step 5) 84
- UG380_c5_07_042909 84
- UG380_c5_08_042909 84
- Startup (Step 8) 86
- Phase Event 87
- Signal Name Type Access 88
- Bitstream Encryption 89
- Loading the Encryption Key 90
- Loading Encrypted Bitstreams 90
- Configuration Memory Frames 95
- Type 1 Packet 96
- Type 2 Packet 96
- Configuration Registers 97
- CRC Register 98
- CBC_REG Register 100
- IDCODE Register 100
- CSBO Register 100
- Command Register (CMD) 100
- Control Register 0 (CTL) 101
- Status Register (STAT) 102
- Configuration Packets 103
- Suspend Register (PWRDN_REG) 104
- Frame Length Register 104
- Multi-Frame Write Register 104
- HC_OPT_REG Register 105
- MODE Register 106
- CCLK_FREQ Register 107
- PU_GWE Register 107
- PU_GTS Register 107
- SEU_OPT Register 108
- DNA_PORT 109
- UG380_c5_14_052009 110
- Read = 0 110
- X = Don’t care 110
- ↑ = Rising clock edge 110
- UG380_c5_15_121112 111
- UG380_c5_16_021010 111
- UG380_c5_17_052009 112
- UG380 (v2.7) October 29, 2014 113
- Readback and Configuration 115
- Verification 115
- Readback Command Sequences 116
- AA 99 55 66 28 00 E0 0 0 117
- Verifying Readback Data 127
- UG380_c6_04_042909 128
- MSK and BIT Files 129
- Reconfiguration and MultiBoot 131
- Fallback MultiBoot 132
- IPROG Reconfiguration 134
- Watchdog Timer 135
- Readback CRC 137
- CRC Masking 138
- Chapter 8: Readback CRC 140
- Distributed RAM 141
- Post_CRC Constraints 142
- POST_CRC 143
- POST_CRC_INIT_FLAG 143
- POST_CRC_SOURCE 143
- POST_CRC_ACTION 144
- POST_CRC_FREQ 144
- Chapter 9 145
- Mixed Serial Daisy-Chains 146
- Startup Sequencing (GTS) 147
- Active DONE Driver 147
- Connect All DONE Pins 147
- DONE Pin Rise Time 147
- Bitstream Formatting 147
- Parallel Daisy-Chain 151
- Ganged SelectMAP 152
- UG380_c9_06_021710 153
- ABORT Status Word 154
- SelectMAP Reconfiguration 155
- Advanced JTAG Configurations 157
- JTAG Configuration/Readback 158
- Boundary-Scan Register 161
- Instruction Register 162
- UG380_c10_03_102014 162
- BYPASS Register 164
- JTAG Configuration Register 164
- USERCODE Register 164
- Load CFG_IN 166
- Instruction 166
- Single Device Configuration 167
- Multiple Device Configuration 168
Produits connexes et manuels pour Les démarreurs à distance Autostart PD-2.7
(112 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels