MANUAL TRANSMISSION REMOTE STARTER PS-3085SH Installation Guide Notice The manufacturer will accept no responsibility for any electrical damage res
P. 10 Installation Guide PS-3085SH 12 YELLOW (+) Glow-Plug input (cont.) (Also known as the “wait-to-start light”.) The purpose of the Glow-plug ci
PS-3085SH Installation Guide P. 11 12 YELLOW (+) Glow-Plug input (cont.) o Minimum waiting time is 3 seconds. o Maximum waiting time is 18 second
Here are the steps which the installer must follow in order to flash the Hood Pin switch: The Installer … The Module … Press and hold the Hood Pin sw
PS-3085SH Installation Guide P. 13 memory, you must perform a reset of the Remote Car Starter (see Resetting the Remote Car Starter, later in this G
P. 14 Installation Guide PS-3085SH Table 4: Accessing options In each Function, once an Option has been selected the Parking Lights will flash 1, 2,
PS-3085SH Installation Guide P. 15 FUNCTION 3 – Turbo Mode OPTION 1 Turbo Mode ENABLED OPTION 2* Turbo Mode DISABLED OPTION 3 Turbo Mode ENABLED
P. 16 Installation Guide PS-3085SH adjustment. Nevertheless, a Tach-programming procedure must be carried out every time a new Remote Car Starter Un
PS-3085SH Installation Guide P. 17 a. To increase the Horn pulse by 3 ms, press the LOCK button. b. To decrease the pulse by 3 ms, press the UNLOCK
P. 18 Installation Guide PS-3085SH Remaining in ready Mode Once the vehicle is in Ready Mode, you can start and stop the vehicle at wish. However, s
Most comebacks are the result of misunderstandings about how a product works or performs. Take the time to properly explain all functions and features
P. 2 Installation Guide PS-3085SH Table of ContentsTable of Contents... 2 Introduction ...
P. 20 Installation Guide PS-3085SH test the wire with the Key in the START position With the pedal down: test the wire with the Ignition Key in the OF
PS-3085SH Installation Guide P. 21 Note on N/C systems: There are different types of this system used by various vehicle manufactures, the following
If the vehicle is initially unlocked, upon remote START the Remote Car Starter will start the Engine and arm the Starter Kill, but the Doors will not
PS-3085SH Installation Guide P. 23 2. Press and release the Break Pedal 6 times (within 10 seconds from entering Programming Mode). 3. The Parking
P. 24 Installation Guide PS-3085SH Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, Starter Kill armed. • End of Run T
PS-3085 Wiring Diagram PS-3085 Installation Guide
PS-3085SH Installation Guide P. 3 INDUSTRY CANADA USER NOTICE: Operation is subject to the following two conditions: (1) this device may not cause
P. 4 Installation Guide PS-3085SH When joining all Door Pins together to the Door Pin input wire of the Remote Car Starter unit, each wire must be
PS-3085SH Installation Guide P. 5 Connect to the Ignition wire of the vehicle. The source wire should have +12 V with the Ignition Key in the IGNITI
P. 6 Installation Guide PS-3085SH This wire will allow the Remote Car Starter to sense whether the Engine is running. The wire requires at least 1.8
PS-3085SH Installation Guide P. 7 4 WHITE / BROWN (–) Rearm output 500 mA ground signal when the Doors are locked by remote control. This wire will
P. 8 Installation Guide PS-3085SH 9 PURPLE (–) External Trigger The External Trigger wire can be used for remote-starting the vehicle with an exter
PS-3085SH Installation Guide P. 9 Caution! If multiple relays or modules are connected to the GROUND OUT WHEN RUNNING wire, make sure they are
Commentaires sur ces manuels